JT JT700 on TrackeraX
The JT JT700 is a GPS tracker that works with TrackeraX over the jt600 protocol on port 6014. From the platform it supports engine stop, engine resume and set time zone, plus custom commands. The server decodes 11 alarm types from this protocol, such as fatigue driving, fault and geofence entry.
[ How to connect it to TrackeraX ]
- Insert a SIM card with mobile data and set the APN of your carrier on the device.
- Set the server to the domain of your TrackeraX platform and the port 6014 (jt600 protocol).
- Create the device in TrackeraX with its IMEI or identifier and choose the JT JT700 model.
- Wait for the first position and turn the parameters above into sensors and alerts.
The exact commands to set the APN and server depend on the firmware: check the manufacturer's manual or ask our support team.
[ Commands you can send from TrackeraX ]
Available from the web platform and the apps. The custom command sends any text the device firmware accepts.
- Engine stopengineStop
- Engine resumeengineResume
- Set time zonesetTimezone
- Reboot devicerebootDevice
- Custom commandcustom
[ Data reported by the jt600 protocol ]
Parameters the server decodes from this protocol. In TrackeraX you turn them into sensors, alerts and reports. Each model reports the ones its firmware and wiring allow.
- Battery levelbatteryLevel
- Blockedblocked
- Chargingcharge
- Doordoor
- Driver ID (RFID / iButton)driverUniqueId
- Fuelfuel
- GPS statusgps
- Humidityhumidity
- Ignitionignition
- Odometerodometer
- External powerpower
- GSM signalrssi
- Satellitessat
Numbered inputs and sensors
- Temperature sensors (temp1, temp2…)
[ Alarms the protocol can report ]
- Fatigue drivingfatigueDriving
- Faultfault
- Geofence entrygeofenceEnter
- Geofence exitgeofenceExit
- GPS antenna cutgpsAntennaCut
- Low batterylowBattery
- Overspeedoverspeed
- Power cutpowerCut
- SOSsos
- Towingtow
- Vibrationvibration
[ Protocol-specific attributes ]
alertType · backCap · eventSource · fuel1 · fuel2 · fuel3 · lbs · sensorBattery · sensorBatteryLevel · sensorRssi · steelCable
[ Other JT models ]
[ Other devices on the jt600 protocol ]
JT JT700 FAQ
Which port does the JT JT700 use to connect to TrackeraX?
The JT JT700 uses the jt600 protocol and connects to port 6014 on your TrackeraX server. Just set your platform domain and that port on the device.
What data does the JT JT700 send to the platform?
TrackeraX reads 14 parameters of the jt600 protocol on this device, for example: Battery level, Blocked, Charging, Door, Driver ID (RFID / iButton). Each one can become a sensor or an alert.
Can I send commands to the JT JT700 from TrackeraX?
Yes. From the map or the device page you can send 4 command types to the JT JT700, including: Engine stop, Engine resume, Set time zone, Reboot device.
Which alarms does the JT JT700 report?
TrackeraX recognizes these jt600 alarms: Fatigue driving, Fault, Geofence entry, Geofence exit, GPS antenna cut. Any of them can become an email, push or webhook notification.
How do I add the JT JT700 to my platform?
Insert a data SIM, set the APN, point the device to your platform domain on port 6014 and create it in TrackeraX with its IMEI, choosing the JT JT700 model.
Try the JT700 on your own platform
Open the live demo or check the plans: white label, your domain, your apps.
Brands, logos and product images belong to their respective owners.

